Battery (bottle) working principle - power circuit - circuit diagram - Huaqiang Electronic Network

MOS power IC full range

Industrial Router Crystal 3.2*2.5mm 3225 26M (26.000MHZ) 12PF 10PPM 20PPM 30PPM

inductance

SMD aluminum electrolytic capacitor

How the battery (bottle) works

As a stable power source and a main DC power source, the lead-acid battery works as “double sulphation theory”. The electrode reaction and battery reaction of the battery are as follows:
Negative electrode: Pb+H2SO4-2e- PbSO4+2H+
Positive electrode: PbO2+H2SO4+2H++2e- PbSO4+2H2O
Battery reaction: Pb+2H2SO4+PbO2 2PbSO4+2H2O
The structural components are mainly positive electrode plates (PbO2), negative electrode plates (alloys such as lead calcium or lead bismuth), grids (metal alloys), etc., lead-acid batteries form PbSO4 crystals during discharge, and lead ions in PbSO4 are reduced during charging. It is a metal lead, thereby realizing the conversion of electric energy chemical energy.

Battery (bottle) failure
Studies have shown that batteries are improperly maintained in actual use, such as frequent charging, long-term over-discharge, and deep discharge. On the positive and negative plates of the battery, a hard and poorly conductive crystalline lead sulfate (PbSO4) is gradually formed. This lead sulfate crystal is charged by a conventional method, and it is difficult to reduce the reaction with it. Very poor, its own power consumption, a large amount of heat to release a large amount of gas, this phenomenon is called "irreversible sulfation", referred to as "vulcanization" or "salting." The battery has increased internal resistance due to vulcanization, and the capacity is reduced, and the battery is even scrapped because it cannot be charged. In practical use, lead-acid batteries can be known from the recrystallization process of lead sulfate. Small crystals are decomposed by charging on the one hand, and recrystallized by discharge on the other hand. This decomposition and recrystallization process will remain on the plates. The crystals are getting more and more, and the vulcanization of batteries is becoming more and more serious. Therefore, the vulcanization of lead-acid batteries is an inevitable phenomenon. To improve the storage capacity of batteries and prolong the service life of batteries, it is necessary to make an article on vulcanization. The computer numerical control battery (bottle) regeneration repair system developed by Zhengzhou Europe and America Electronic Technology Co., Ltd. can Break the crystal of the battery, restore the function of each component, and improve the battery vitality.

Computer numerical professional repair technology
"Lead-acid battery resonant composite pulse special effect repair technology" is the battery expert group of Zhengzhou Europe and America Electronic Technology Co., Ltd. combined with its own strong scientific research strength, strengthen independent innovation, and solve the worldwide problem of "irreversible vulcanization" of lead-acid batteries, using the latest nano-synthesis Technology and international cutting-edge theory, developed a new high-tech that can restore vulcanized batteries.
This technology combines the theory of physical and chemical elimination of vulcanization, can effectively remove the sulfide of the battery plate, achieve the cleaning of the battery plate at all times, maintain, maintain and repair the lead-acid battery, and maintain the brand new state. Stabilizing the battery capacity output completely and completely changes the battery sulfation phenomenon, maximizing the battery life. After the regeneration and recovery of the lead-acid battery, its capacity can be restored to the original factory standard capacity. In the lead-acid battery that has been scrapped and scrapped, as long as it is produced by the regular manufacturer according to the standard, whether it is imported or domestic, ordinary or maintenance-free, rich liquid or poor liquid, as long as it is scrapped due to vulcanization. (In addition to physical damage, such as: plate off, internal open circuit, short circuit, etc.), can be repaired by this system. Repairing a set of waste batteries requires only one kilowatt hour, and the charge ranges from 80 to 500 yuan. The profit margin is huge.

Technical principle

In view of eliminating the principle that the battery vulcanization utilizes the pulse harmonic component, the pulse generation can improve the repair effect. The system uses the most advanced resonant composite pulse repair technology. By measuring the battery status. Positive and negative frequency conversion pulses are continuously emitted while charging and discharging. Resonance with the lead sulfate crystals in the battery, thereby reducing the lead sulfate crystals to sulfur and lead ions. Change the composition and properties of the dielectric. Generate 300,000 sets of composite pulses per second to improve repair efficiency (resonance frequency up to 1 MHz). Open the ion channel, fully release and activate the original active material, so that it has stronger electrochemical ability, reduce the internal resistance of the battery, and completely eliminate the battery vulcanization. The lead-acid battery that has been regenerated and restored can recover its capacity to over 99.66% or even 100% of the original nominal capacity.